How to Measure O-Rings: ID, Cross Section and OD Guide
Updated: Nov 16, 2026
How to measure O-rings comes down to two dimensions: the inside diameter (ID) and the cross section (CS), the thickness of the cord. Use calipers with light pressure for CS, and a sizing cone or pi tape for ID. Then match both numbers to an AS568 dash number or a metric ID x CS size.
Not sure your numbers point to one size? Send them to our engineering team and we will help you match the part.

What you measure on an O-ring: ID, CS and OD
Knowing how to measure O-rings starts with knowing which dimensions matter. An O-ring has three dimensions, but only two of them define its size.
- Inside diameter (ID): the distance across the hole, from inner edge to inner edge.
- Cross section (CS): the thickness of the rubber cord itself. Some charts call it width (W).
- Outside diameter (OD): the distance across the outer edges. OD = ID + 2 × CS.
Standard size charts are built on ID and CS. Our AS568 O-ring size chart notes that OD is a reference dimension only; ID and CS, with their tolerances, are the controlling sizing dimensions. So if you can only take two measurements, take ID and CS. Measure OD only when it is the easier way to get to ID, as with large rings.
Tools for measuring O-rings
The right tool depends on the size of the ring and how close the nearest standard sizes are. Rubber is soft, so any tool that squeezes or stretches the ring will give you a smaller CS or a larger ID than the real part.
| Tool | Measures | Best for | Watch out for |
|---|---|---|---|
| Calipers (digital or dial) | CS; ID or OD of small, firm rings | Cross section on any O-ring | Squeezing the cord reads low; close the jaws until they just touch |
| O-ring sizing cone | ID | Small and mid-size rings | Let the ring drop under its own weight; do not push it down the cone |
| Pi tape (diameter tape) | OD, then ID = OD − 2 × CS | Large rings | The tape must sit flat and snug around the full ring |
| O-ring sizer card or gauge | CS and ID by comparison | Quick checks at the bench or in the field | Comparison only; confirm close calls with calipers |
| Non-contact optical measurement | ID, OD and CS | Very small, soft or critical parts | Needs inspection equipment |
| Ruler or tape measure | Rough ID | Last resort | Not precise enough to separate neighboring sizes |
For most jobs, a pair of calipers and a sizing cone or pi tape is enough. For tiny or very soft parts, or when a size is critical, non-contact optical measurement removes the squeeze error completely.
How to measure O-rings, step by step
- Clean the ring and let it relax. Wipe off grease and dirt. Lay the ring flat on a clean surface without stretching or twisting it.
- Measure the cross section first. Close the caliper jaws on the cord until they just touch, without flattening it. Measure at 3 or 4 spots around the ring and average the readings.
- Measure the inside diameter. For small and mid-size rings, slide the ring onto a sizing cone and let it settle under its own weight; read the ID where it stops. For large rings, wrap a pi tape around the outside to read OD, then subtract 2 × CS.
- Record both units. Write down inches and millimeters. To convert, divide millimeters by 25.4.
- Match a standard size. Find the CS first, then the closest ID in that series on the AS568, metric or JIS chart.

Measuring the CS first is the shortcut. Standard O-rings come in a small number of cross sections, so CS narrows the search to one series before you compare IDs.
Have a ring that will not match any chart? Request a quote for the size you measured; non-standard sizes can be made as custom O-rings.
Stretch, shrink and swell: why a used O-ring can mislead you
A new O-ring from a bag is the easiest ring to measure. A ring pulled out of a machine is not. Service changes its shape, so its measurements can point to the wrong size.
- Compression set: after long service in a groove, the cord can take a flat set and stop being round. CS measured across the flat reads low. Read more on compression set in elastomers.
- Swell or shrink: fluids and heat can make a ring grow or shrink compared with its original size.
- Stretch: a ring that sat stretched over a shaft or piston may have a larger ID than when new.
- Damage: cut, nicked or broken rings cannot be measured reliably.
If the old ring is swollen, flattened or damaged, measure the groove (gland) instead and size the O-ring from the groove dimensions. Our general groove design guide covers squeeze, stretch and gland fill, and the face seal groove calculator checks a size against your groove. If you also need to know what the old ring was made of, a bounce test can help identify the elastomer family.

Matching your measurements to AS568 and metric O-ring sizes
AS568 (inch) sizes. The dash number groups O-rings by cross section. Once you know CS, you know which series to search.
| AS568 dash numbers | Nominal CS (in) | Actual CS (in) | Actual CS (mm) |
|---|---|---|---|
| -004 to -050 | 1/16 | 0.070 | 1.78 |
| -102 to -178 | 3/32 | 0.103 | 2.62 |
| -201 to -284 | 1/8 | 0.139 | 3.53 |
| -309 to -395 | 3/16 | 0.210 | 5.33 |
| -425 to -475 | 1/4 | 0.275 | 6.99 |

Metric sizes are named ID x CS in millimeters. A 20 x 2 O-ring has a 20 mm inside diameter and a 2 mm cross section, as our metric O-ring size chart explains. Many metric sizes have a close AS568 match. Our AS568 chart gives this example: a 25 x 3.5 mm O-ring is 0.984 in ID x 0.138 in CS, and the closest AS568 size is -214 (0.984 in ID x 0.139 in CS).
JIS sizes. Japanese equipment often uses the JIS B 2401 standard, which names each O-ring with a series letter and a number. The letter gives the series: P sizes are for dynamic and static seals, G sizes for static gaskets, and V sizes for vacuum flanges. The number is the nominal diameter in millimeters, so P20 is a P-series O-ring for a 20 mm diameter and G50 is a G-series gasket for 50 mm. The nominal number is not the exact inside diameter. Measure the ID and CS in millimeters, then find the matching size on our JIS O-ring size chart. As with AS568 and metric O-rings, ID and CS define the size, and OD is a reference only. In our store, JIS parts are listed by CS x ID in millimeters, not by the JIS code.
Close is not the same as identical. Check compression and gland fill in your groove before you swap a metric ring for an AS568 ring, or the other way around. For background on the inch standard, see AS568: the O-ring size standard.
A note on Canyon part numbers. In our store, AS568 parts end in the dash number (for example -OR-214). Metric and JIS parts end in CS x ID, so the cross section comes first in the part number even though size charts list ID first.
Your measurement may also fall between two standard sizes. Standard sizes carry tolerances, so a reading slightly off a chart value can still be that size. Our RMA and ISO 3601 tolerances page explains how tolerances work for O-rings and molded parts.
When measuring is not enough
Measuring tells you the size. It does not tell you whether that size is right for the job. If the old ring leaked, extruded or failed early, copying its size can repeat the failure. In that case, start from the groove and the operating conditions, not the old ring.
Want a second opinion on the size and the groove before you order? Our engineering services team helps with size, material and groove checks.
FAQ: measuring O-rings
How do you measure an O-ring? Measure the inside diameter (ID) and the cross section (CS). Use calipers with light pressure for CS and a sizing cone or pi tape for ID, then match both to an AS568 or metric size chart.
Are O-rings measured by ID or OD? O-rings are sized by ID and CS. OD is a reference dimension; you can calculate it as ID + 2 × CS, or measure OD on large rings and subtract 2 × CS to get the ID.
How do I measure O-ring cross section? Close the caliper jaws on the cord until they just touch, at 3 or 4 spots around the ring, and average the readings. Squeezing the cord gives a reading that is too small.
Can I measure an O-ring with a ruler? Only roughly. A ruler can get you close on ID, but it cannot reliably separate neighboring standard sizes, and it cannot measure the cross section well.
What if my O-ring is between two standard sizes? Check the tolerances for that size first, then measure the groove. If neither standard size fits the groove, a custom size may be the better answer.
Still between sizes? Contact us with your ID, CS and groove dimensions and we will point you to the right part.
Find your O-ring
Once you have your ID and CS, shop O-rings by size, material and hardness, with live price and stock online. For anything not listed, request a quote or contact us. Same-day quotes are available for most inquiries.






